Improvement by Heat Treatment of the Mechanical Properties of a Grooving Cutter
| Authors | B. Chermime1,2, K. Mansouri2 , H. Djebaili1 , H. Hadjela1, O.A. Abbassi1, O. Hamidane1 |
| Affiliations |
1University Abbes Laghrour, Khenchela, 40000, Algeria 2Laboratory of Engineering and Sciences of Advanced Materials (ISMA), Khenchela, 40000, Algeria |
| Е-mail | cherbrah@yahoo.fr |
| Issue | Volume 16, Year 2024, Number 2 |
| Dates | Received 17 December 2023; revised manuscript received 23 April 2024; published online 29 April 2024 |
| Citation | B. Chermime, K. Mansouri, H. Djebaili, et al., J. Nano- Electron. Phys. 16 No 2, 02025 (2024) |
| DOI | https://doi.org/10.21272/jnep.16(2).02025 |
| PACS Number(s) | 61.46. – w, 62.20.Qp, 68.55Nq |
| Keywords | Grooving cutter, Heat treatment (2) , Martensitic phase, Carbides, Residual austenite, Hardness (12) . |
| Annotation |
Our work entitled improvement of the mechanical properties of a Z80WCV 18-04-01 high-speed steel grooving cutter (three sizes) by heat treatment, the latter can play an essential role in improving the mechanical and structural properties of grooving mills. The results obtained showed that the heat treatments allow to obtain a favorable microstructure, with a martensitic phase formation and a homogeneous distribution of carbides. These structural changes have led to an increase in the hardness, strength and durability of the milling cutters to be grooved in addition, it has been observed that the application of cumulative revenues has a significant impact on the mechanical and structural properties. The successive revenues favored the transformation of quenching martensite into tempering martensite and the elimination of residual austenite, leading to a gradual increase in hardness and wear resistance. |
|
List of References |
Other articles from this number
1) Effect of Introduction Layers of Native Oxide, InN, and InSb on the Electrical Characterization of the Au/n-InP [02001-1-02001-6]2) Performance Enhancement of the Urdhva-Tiryagbhyam based Vedic Multiplier using FinFET [02002-1-02002-5]
3) Analysis of Buckling Behavior of Functionally Graded Plates Under Mechanical Loading [02003-1-02003-4]
4) Effect of GaSb Compound on Silicon Bandgap Energy [02004-1-02004-4]
5) DFT Modeling of Chemical Reactions Occurring Under the Influence of Positive Ionic Complexes of Aqueous HF Solutions During Electrochemical Etching of Silicon [02005-1-02005-5]
6) A Hepta-band Frequency Tunable Patch Antenna for Cognitive Radio Applications [02006-1-02006-6]
7) Fe2O3/p-InSe Heterostructures Produced by Spray Pyrolysis Method [02007-1-02007-4]
8) Transmission and Absorption of Bilateral Porous Silicon with Macropores or Nanowires [02008-1-02008-7]
9) Dual-Band MIMO Circular Patch Microstrip Antenna (CPMA) with Low Mutual Coupling for 5G Communication System [02009-1-02009-5]
10) A New GAA FinFET without n-well or p-well [02010-1-02010-5]
11) Enhancement in the Sensing Efficacy of ZnO-based Ethanol Sensor: Fe-ZnO Film [02011-1-02011-7]
12) Establishment of the Prospective CZTGS Photovoltaic through the Optimization of Some Device Parameters [02012-1-02012-4]
13) Formation of Nitrogen Supersaturated (Nitrogen-Rich) MeN Nitrides at Thermobaric Sintering of PcBN Composites of cBN-{TiN, ZrN, HfN, VN, NbN}–Al Systems [02013-1-02013-7]
14) Electrodynamic Properties of Resonator Probes for Local Microwave Diagnostics of Nanoelectronic Objects [02014-1-02014-6]
15) Design of a High Efficiency Monopole Antenna Array for GPR Application [02015-1-02015-5]
16) Bandwidth Enhanced and Gain Improvement of Compact Patch Antenna Using Metamaterials for UWB applications [02016-1-02016-6]
17) Field Enhancement with Waveguide Resonance by the Structure Dielectric Grating/Dielectric Layer/Metal Substrate [02017-1-02017-5]
18) Improving the Performance of CZTS/CZTSSe Tandem Thin Film Solar Cell [02018-1-02018-6]
19) Ionizing Radiation Detection Using the Field Effect Transistor Based on Reduced Graphene Oxide [02019-1-02019-4]
20) Effect of Additive (MnO) on Dielectric Constant and Dielectric Loss of Na2O-B2O3 Glasses [02020-1-02020-4]
21) Modeling of X-Ray Phase Contrast Imaging of Optically Heterogeneous Objects [02021-1-02021-6]
22) Optimizing Terahertz Signal Detection in High Electron Mobility Transistors: Insights from Plasma Resonance Studies [02022-1-02022-6]
23) Equivalent Circuit Model to Reach Complicated Surface Photovoltage Transient Shapes in ZnO Thin Films [02023-1-02023-6]
24) Li-ion Diffusion in Porous Carbon Electrode Materials by GITT Method [02024-1-02024-4]
25) Structure and Properties of Wear-Resistant Nanostructured Coatings Based on W, Cr and N [02026-1-02026-6]
26) Synthesis of Surface Nanostructures of Silver Sulfide in Argon at Atmospheric Pressure in a Gas Discharge [02027-1-02027-6]
27) Modeling and Simulation of Photovoltaic Panel Using Simulink and Proteus Simulation [02028-1-02028-8]
28) Analysis of Compact Quadruplet Arrow Slotted Notch Band Antenna with Defected Ground Structure [02029-1-02029-5]
29) Properties of the Original Electron-Irradiated LEDs Homojunction GaP, GaAsP and Heterojunction InGaN Structures [02030-1-02030-6]
30) Design of a Split Ring Resonators-Based Band Pass Filter with Triple Pass Band Characteristics for Wireless Communication Systems [02031-1-02031-5]
